Welcome to the crew · Owner guide
Start with the written setup. Enjoy the wash.
No account. No
registration.
Real pressure-washer hardware. Treat it that way.
The Lightspeed Blaster is a pressure-washer accessory, not a toy. Adults only. Keep children, pets and bystanders away from the work area. Read this guide and the instructions for your pressure washer, hose and every accessory before operating.
Never point the nozzle at yourself, another person or an animal. Keep hands and all other body parts away from the spray. Never use your hand to find or stop a leak. High-pressure water can cause severe injury even when the wound looks small. Seek immediate medical attention for a suspected injection injury and tell the clinician that a pressure washer was involved.
Wear suitable eye protection, closed-toe slip-resistant footwear and protective clothing. Follow your washer’s additional protective-equipment requirements. Use a secure two-handed grip, keep hands behind the nozzle and brace for recoil. Stand on stable ground; do not operate from a ladder or while overreaching. Never secure the trigger in the ON position or bypass the trigger lock.
Before changing a nozzle, hose, fitting or accessory, stop the pressure washer and shut off its water supply following its instructions. Point the gun in a safe direction and squeeze the trigger to relieve residual pressure. Engage the trigger lock before disconnecting anything. A pressurized nozzle or fitting can eject with force. Never look into a connected nozzle.
Keep spray away from electrical equipment, outlets and the pressure washer itself. Do not submerge the Blaster or direct a pressure-washer jet at its housing. Keep the USB cover fully closed during use. Do not charge in wet conditions or operate while charging.
Provide enough area lighting to see the surface, people, hose and footing; the Blaster’s LEDs do not replace adequate work lighting. Use gasoline-powered pressure washers outdoors, away from doors, windows and vents, as directed by their manufacturer. Never run them inside a garage or other enclosed space.
Before each wash: inspect the gun, hose, couplers, adapter, nozzle, trigger, lock and USB cover. Do not use a cracked, damaged or leaking part, a loose nozzle, or a trigger that sticks or does not stop the spray. If the unit has been dropped, inspect it before use; stop and contact support if damage or safe operation is uncertain.
Disconnect the charging cable, make sure the port is dry and close its cover before washing. See charging instructions.
Check washer pressure, flow, hose fitting and nozzle size. Check every connected part’s rating. Do not force mismatched fittings.
Connect a compatible 3/8-inch female quick-connect hose fitting to the Blaster’s 3/8-inch male swivel inlet. For a compatible M22-14 mm hose, use the included adapter. M22-15 mm and proprietary fittings need a separately verified adapter.
With power off, water shut off, pressure relieved and trigger locked, fully insert the nozzle. Tug to verify retention. Check hose retention too. Do not use a loose connection.
Turn on the water and follow the washer’s air-purge and startup instructions. Maintain a secure grip and point at a safe cleaning area. Begin at a conservative distance with a suitable wide spray and test an inconspicuous area.
The trigger activates lights and sound together; the color button cycles six colors, including white. Water still flows with a depleted battery. Loss of lights or sound does not mean pressure is relieved.
Use clean water through the gun. A compatible downstream foam cannon may add detergent after the gun. No chemicals, solvents or flammable liquids through the gun. Follow the foam cannon’s instructions.
The included tips have size-2.5 orifices. The color identifies the spray angle, not a guaranteed safe pressure for a surface. Match the orifice to your washer’s operating pressure and flow. Ask support if you are unsure; do not rely on the valve’s 12 GPM rating when choosing a nozzle.
Consider first for compatible delicate surfaces, using suitable pressure and distance. Test first.
For suitable surfaces. A closer or more concentrated spray can damage finishes.
More aggressive spray for suitable durable surfaces. Use extra care.
High injury and damage risk. Do not use on vehicle paint, glass, tires, skin or other vulnerable surfaces.
Stop the washer, shut off water, relieve pressure and lock the trigger before changing tips. Fully seat and check the new tip before use.
USB charging input: 5V DC, 1A. Use the included cable and an undamaged, reputable USB power supply suitable for that input. The internal battery’s 3.7V rating is not the USB input voltage. If a power supply’s compatibility is unclear, contact support before charging.
Charge indoors in a dry location, on a stable noncombustible surface, away from heat and flammable materials. The gun, cable, hands and charging port must be dry. Do not charge while washing, when submerged or after suspected water entry. Disconnect after charging and close the USB cover fully before use.
Do not crush, puncture, short-circuit, burn or modify the battery. Do not expose it to temperatures above 122°F (50°C), as stated on the supplied leaflet. Do not leave the product in a hot vehicle. The maximum water temperature is not a permissible battery storage or charging temperature.
Stop use and charging if the unit swells, leaks, smells unusual, becomes unusually hot or shows battery damage. Contact support for handling instructions. Do not send a damaged battery product through ordinary mail without approved shipping instructions. If there is smoke or fire, move away and call emergency services.
Temperature clarification: the supplied leaflet states 140°F. Lightspeed confirms a maximum water temperature of 150°F for this model. Always follow the lowest applicable limit in your complete setup.
Shut down the washer, turn off water and relieve pressure with the nozzle pointed safely. Engage the trigger lock, disconnect as instructed and drain residual water. Let the exterior dry. Store indoors in a dry location out of children’s reach and protected from freezing. Never allow trapped water to freeze inside the gun.
Do not lubricate, tighten, disassemble or replace internal parts while pressurized. Contact support before internal servicing. Battery and electronic repairs require appropriate expertise. Dispose of the battery-containing product through an appropriate local battery or electronics collection service, not household trash.
Lightspeed Blaster, LLC warrants the Lightspeed Blaster against defects in materials and workmanship for one year from the original retail purchase date. This includes the gun’s mechanical and electronic components and battery, subject to the exclusions below. O-rings are excluded from this limited warranty. Keep your receipt or order confirmation as proof of purchase.
For V-01 Launch Edition units, the one-year coverage stated here applies even if the supplied leaflet refers to six months. Registration or scanning the QR code is not required to receive warranty service.
These damage exclusions apply when the listed conduct or condition causes the problem. Opening the housing, using third-party parts or obtaining independent service does not by itself cancel coverage for an unrelated manufacturing defect.
For an approved claim, Lightspeed will provide replacement parts or a replacement unit, at its discretion, without charge for the covered remedy. Lightspeed covers shipping within the United States for approved warranty service, including an authorized return if required. Contact us before arranging shipment or repair. We will explain the remedy and any safe installation or return instructions.
This warranty gives you specific legal rights, and you may also have other rights which vary from State to State. Nothing in this warranty excludes rights or remedies that cannot lawfully be excluded.
Lightspeed Blaster, LLC
Pasco, WA 99301
support@lightspeedblaster.com
We do not accept discretionary change-of-mind returns or exchanges. This does not limit the one-year limited warranty, our obligations for incorrect or damaged deliveries, or cancellation and refund rights required by law.
If an order arrives damaged, incomplete or incorrect, contact support promptly with your order details and available photos. Retain the packaging while we review the issue. Do not use a product that appears unsafe, and do not return it without instructions from our team.
Current preorders are expected to ship by early November 2026. This is an estimated shipment window, not a delivery date. Carrier transit time begins after your order ships. Shipping destinations, eligibility and any applicable shipping charges are shown before you complete checkout.
If we cannot ship within the stated window, we will notify you and provide the applicable options to consent to a delay or cancel for a full refund. If we cannot fulfill your order, we will notify you and refund it as required by law. Contact support@lightspeedblaster.com with questions about your order.
Need a hand?
Send your washer model, order number and a description of the issue. Include available photos of the fittings or problem. Do not recreate an unsafe condition for a photo or video.
support@lightspeedblaster.com
Lightspeed Blaster, LLC · Pasco, WA 99301
Contact us before
returning a unit. We provide the authorized destination and shipping
instructions directly.